I have a Focusrite Scarlett 2i2 audio interface and a Yamaha MG16/6FX mixer and I am considering to use the Scarlett 2i2 as an interface to a condenser microphone (to be recorded using the USB out). My question is, how should I connect the output from the audio interface to my mixer? The Scarlett 2i2 has a stereo L/R balanced TRS jack. Vertical hold head first %5b1995%5d.rar. How to connect setup add analog summing mixer to audio daw interface soundcard Technical questions User manual troubleshooting signal loss ground loop noise. I realized that no audio at all was coming from the mixer, either in our out, so I scrapped the last connection, bought an official apple lightning to USB camera adapter and a new USB 2.0 cable. Plugged it in and my previously recorded audio now comes through the mixer on playback, but now it will not register any input from any channel from. If you have a two-channel audio interface, you can do the same thing. You can connect many microphones to your mixer, connect the left and right outputs of your mixer to the inputs of your audio interface. Listen with headphones to create a good mix of all instruments, then press record in your DAW.
in Support and Feedback
Connecting Mixer To Audio Interface Arduino
Hi - I’ve been using Loopy for a while and it works perfectly. Today I tried setting it up through an audio interface with microphone and headphones (eventually I want to use that interface to connect it to a PA system). However, loopy keeps using the iPad speakers and not run through the interface. (Zoom U24). Is loopy not recognizing my interface? Or is there a setting I need to change?
Connect Mixer To Audio Interface For Recording
Comments
Connecting Mixer To Audio Interface Download
Copying my email to you here for posterity, @diane123:
Whole Home Mesh WiFi Systems Range Extenders Modem Routers. Products certified by the Federal Communications Commission and Industry Canada will be distributed in the United States and Canada. Please visit the ASUS USA and ASUS Canada websites for information about locally available products. All specifications are subject to change without notice. Please check with your supplier for exact offers. ASUS EN7600GS Silencer Series equip with the Supreme silent heatsink, newest ASUS-specific award-winning features and nVidia®´s GeForce 7600GS Graphics Processing Unit (GPU), which owns both ultimate excellent cinematic resolution and fierce graphics computing power. Asus en7600gs silent driver windows 10 64 bit.
Can you tell me what happens when the U-24 is connected? I take it the audio input is still coming from the microphone, and output is still going through the device speaker? That would indicate to me perhaps a problem with the cable, if not the U-24 itself. Also try rebooting the device, just in case. Let me know if you have further trouble.
edited January 2019
i am having the same issue. I am new to Loopy HD and would also like to incorporate it into my live shows. I am just starting to set it up. I am using a Behringer Xenyx X1832 USB mixer. I have connected my iPad 2 to the mixer using a female-female USB coupler in between the factory iPad lighting connecter and a USB cable to the mixer. Input comes through great from the mixer to the iPad, but playback comes through the speakers of the iPad instead of through the mixer. The USB cable I am using from the mixer to the coupler is rather old, though I am not sure if this would make a difference. Any help much appreciated. Thanks!
I realized that no audio at all was coming from the mixer, either in our out, so I scrapped the last connection, bought an official apple lightning to USB camera adapter and a new USB 2.0 cable. Plugged it in and my previously recorded audio now comes through the mixer on playback, but now it will not register any input from any channel from the mixer.
Samsung u28e590d firmware update software. @PAPI I believe the X1832USB only sends and receives the main input/output over USB. This is a limitation of how the X1832 was designed, so you aren't able to isolate a specific channel to go to Loopy. Only the main output from the mixer gets sent to Loopy.
Connecting Mixer To Audio Interface Speakers
Hi, Hope this is the correct section to ask this, if not please advise. I'm having real problems connecting my mixer to my audio interface and getting playback via my monitors/headphones. Connecting via the following method all i get is muddy very quiet playback even on max volume. In fact, i hear nothing until its quite high. Plugging in headphones to the audio interface works fine with the same set up but not when the phones are plugged into the mixer. My mixer 'main out' is unbalanced so i use 2 ts (mono) cables from my mixer into the 2 inputs on the audio interface which is set to 'line' input. (Also have tried trs stereo leads for this connection with the same results). I then connect the 'out' on my mixer to two line outputs on the rear of the audio interface using a twin rca (from the mixer) to ts cables (into the audio interface outputs 1 & 2 on the audio interface. Finally i plug a twin ts lead from the control room out into my monitors (rca inputs). This was following advice from several youtube videos. I dont have any problems recording into my DAW with this set up its just the playback which sounds like its playing under water. Ive tried using ts to ts cables into the speakers as well with the same results.I have also tried trs (stereo) leads into the monitors as well. Ive adjusted all volume controls on the mixer/audio interface/speakers etc with the same results. With this set up if i plug headphones into the audio interface i get clear decent playback, however if i plug the phones into the 'phones' on the mixer i get the same muddy/underwater results. Also if i connect the monitors direct to the audio interface i get decent playback its only when i try to run the monitors/headphones via the mixer. Clearly there is an issue with the way ive set the cables up. The mixer and audio interface are new by the way and function as you would expect apart from this issue with monitors and headphones. Sorry for the lack of technical speak. I hope i've described my problem clearly enough for someone to help. Its driving me absolutely mad! Cheers. My Equipment: Behringer Xenyx 1202 mixer Focusrite 8I6 3rd Gen audio interface Alesis Elevate 5 MK 2